Standard belts include PU 11, PU 12 and NE 22. These belts are available in length increments of 10 mm from 400-1800 mm long and from increments of 20 mm in length up to 2400 mm long. These belts may not be the most ideal belt within your specific application but are generally available with a 2 week delivery and no minimum order requirements. For some applications, they certainly are a perfect solution. When you have any type of special requirements (such as FDA approval) please select Custom Belt.
PU 11
- 55 Shore A foamed yellow PU
- Running side coated, outside textile
- Polyester Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 12 mm
- Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 230 +/- 30 N
- Preferred Lengths up to 2400 mm
- Very good running characteristics
- General applications
PU 12
- 55 Shore A foamed yellow, PU
- Running side coated, outside textile
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm
- Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
- Standard Lengths up to 2400 mm
- General Applications
- Medium Duty Drives
NE 22
- 75 Shore A textured black Neoprene
- Both sides coated
- Polyester Carcass
- Temp Range -20°C to 100°C
- Minimum Pulley Diameter = 20 mm
- Thickness = 1.4
- Required Shaft Load for 1% Elongation: 375 +/- 15 N
- Standard Lengths up to 2400 mm
- General Applications
- Medium Duty Drives
No special Requirements? If your application has no special requirements and your belt size is below 2400 mm, try a standard belt above.
In general, it is recommended to guide Woven Endless flat belts using crowned pulleys. For recommendations on crown dimensions or which pulleys to crown, see pages 14-15 of our B210 Woven Endless Flat Belts catalog. Of course, tracking guides are also an option. If you have any questions or concerns, contact our Applications Engineering department.
Polyurethane Belts (PU)
- Great for General Conveying
- Foamed (yellow, gray, white, red)
- Temperature Range up to 60°C
- Good coefficient of friction to paper
- Different durometers available (30, 55 and 70 Shore A)
- Thickness up to 10 mm
- Surface finishes: ground, non porous ply, low friction coating, silicone skim coat
PU 11
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 12 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 230 +/- 30 N
PU 17
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =15 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 950 +/- 50 N
PU 12
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
PU 18
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =30 mm (at standard thickness)
- Standard Thickness = 2.2 mm
- Required Shaft Load for 1% elongation: 1280 +/- 50 N
PU 0/6
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- No carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =8 mm (at standard thickness)
Standard Thickness: 0.9 mm
- 1.2 mm (from 1000mm length)
- 1.5 mm (from 1500 mm length)
- 2.0 mm (from 2000 mm length)
- Required Shaft Load for 1% elongation: 4 +/- 2 N
- Highly elastic
- friction lining
- for fixed shaft centers
- belts used as sets
- Requires operating or stretched length
PU elastic
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Rubber Cords / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 25 mm (at standard thickness)
- Standard Thickness = 1.8 mm
- Required Shaft Load for 1% elongation: 6 +/- 3N
- Elastic
- For fixed shaft centers
- Belts used as sets
- Requires operating or stretched length
PU elastic 13
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Rubber Cords / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 25 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 8 +/- 2N
- Elastic
- For fixed shaft centers
- Belts used as sets
- Requires operating or stretched length
PU 4/6
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 9 mm (at standard thickness)
- Standard Thickness = 0.8 mm
- Required Shaft Load for 1% elongation: 130 +/- 15N
- Accumulator conveyor
- Paper transport
- Very flexible
PU 10
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester/Polyamide
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 8 mm (at standard thickness)
- Standard Thickness = 0.9 mm
- Required Shaft Load for 1% elongation: 100 +/- 15N
- Slightly elastic
- For fixed shaft centers
- Belts used as sets
PU 20/1
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 9 mm (at standard thickness)
- Standard Thickness = 0.9 mm
- Required Shaft Load for 1% elongation: 165 +/- 15N
- Speed-up conveyor
- Knife edge
- Low coefficient of friction on textile side
PU 20
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 5 mm (at standard thickness)
- Standard Thickness = 0.8 mm
- Required Shaft Load for 1% elongation: 165 +/- 15N
- Thin, highly flexible
Compact Polyurethane (FX)
- FDA
- 80 Shore A
- Temperature Range -10°C - 80°C
- Surface finishes: smooth, ground or textured
- Only available in certain thicknesses
FX 11
80 Shore A, 92 Shore A
Polyester Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 10 mm (at standard thickness)
Standard Thickness = 1.4 mm
Required Shaft Load for 1% elongation: 230 +/- 20 N
FX 10
80 Shore A, 92 Shore A
Coated on both sides (ground one side, textured other)
Polyamide/Polyester Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 15 mm (at standard thickness)
Standard Thickness = 1.0 mm
Required Shaft Load for 1% elongation: 55 +/- 10 N
FX 17
80 Shore A, 92 Shore A
Kevlar Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 20 mm (at standard thickness)
Standard Thickness = 1.3 mm
Required Shaft Load for 1% elongation: 1040 +/- 50 N
FX 20
80 Shore A, 92 Shore A
Polyester/Cotton Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 15 mm (at standard thickness)
Standard Thickness = 0.7-0.9 mm
Required Shaft Load for 1% elongation: 165 +/- 15 N
Silicone (SI)
- FDA
- High and Low Temperature Resistance
- Temp Range: -60°C to 200°C
- 30-35 Shore A, 50 Shore A
- White, Gray, Red, Blue
- High coefficient of Friction
- Resistant to dirt and chemicals
- Great for printing applications
- Thickness up to 10 mm
- Surface finishes: ground, Silicone skim coat (sealed)
SI 1
30 Shore A, 50 Shore A
Polyester Carcass
White, Blue, Gray, Red
Temperature Range: -20°C to 150°C
Minimum Pulley Diameter: 12 mm (at standard thickness)
Standard Thickness = 1.0 mm
Required Shaft Load for 1% elongation: 190 +/- 20 N
SI 3
30 Shore A, 50 Shore A
Polyester/Cotton Carcass
White, Blue, Gray, Red
Temperature Range: -20°C to 120°C
Minimum Pulley Diameter: 10 mm (at standard thickness)
Standard Thickness = 1.0 mm
Required Shaft Load for 1% elongation: 135 +/- 15 N
HN 1
30 Shore A, 50 Shore A
Nomex Carcass
White, Blue, Gray, Red
Temperature Range: -50°C to 180°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 1.5 mm
Required Shaft Load for 1% elongation: 170 +/- 20 N
HG 1
30 Shore A, 50 Shore A
Fiberglass Carcass
White, Blue, Gray, Red
Temperature Range: -60°C to 200°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 1.5 mm
Required Shaft Load for 1% elongation: 600 +/- 50 N
HK 17
30 Shore A, 50 Shore A
Kevlar Carcass
White, Blue, Gray, Red
Temperature Range: -50°C to 200°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 1.3 mm
Required Shaft Load for 1% elongation: 290 +/- 50 N
HK 18
30 Shore A, 50 Shore A
Kevlar Carcass
White, Blue, Gray, Red
Temperature Range: -50°C to 200°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 2.0 mm
Required Shaft Load for 1% elongation: 990 +/- 100 N
Belt Part Description
PN1
PN2
PN3
PN4
Standard Part Description
PN1
PN8
PN7
FX Belt Part Description
PN1
PN2
PN6
PN5
PN4
Required Specific Power [kW/cm]:
Recommended Belt Standard
Required strength is not possible with requested belt width. Please try increasing belt width or contact Applications Engineering for more support
NE 18
- 75 Shore A
- Kevlar carcass
- Temp range -20°C/+100°C
- Minimum pulley diameter = 30 mm (at standard thickness)
- Standard thickness = 2.0 mm
- Required shaft load for 1% elongation: 1700 +- 200 N
- Extremely low elongation
- Heavy-duty drives
NE 26
- 75 Shore A
- Polyester Carcass
- Temp range -20°C to +100°C
- Minimum Pulley Diameter = 25 mm
- Standard thickness = 2.0 mm
- Required shaft load for 1% elongation: 385 +/- 15 N
- Heavy Duty Drives
PU 18
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =30 mm (at standard thickness)
- Standard Thickness = 2.2 mm
- Required Shaft Load for 1% elongation: 1280 +/- 50 N
NE 22
- 75 Shore A
- Polyester Carcass
- Temp Range -20°C to +100°C
- Minimum pulley diameter = 20 mm
- Standard thickness = 1.4 mm
- Required shaft load for 1% elongation: 375 +/- 15 N
- Stocked lengths up to 2400 mm
- General applications
- Medium duty drives
NE 17
- 75 Shore A
- Kevlar Carcass
- Temp range -20°C to +100°C
- Minimum pulley diameter = 12 mm
- Standard thickness = 0.9 mm
- Required shaft load for 1% elongation: 1040 +/- 50 N
- Drive belt
- Very low elongation
PU 12
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
- Stock lengths up to 2400 mm
- General Applications
- Medium duty drives
PU 12
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
- Stock lengths up to 2400 mm
- General Applications
- Medium duty drives
PU 17
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =15 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 950 +/- 50 N
- Very low elongation
NE 21
- 75 Shore A
- Polyester Carcass
- Temp Range -20°C to +100°C
- Minimum pulley diameter = 15 nn
- Standard thickness = 0.9 mm
- Required shaft load for 1% elongation: 270 +/- 10 N
- High belt speeds
- Very good running characteristics
- General applications
PU 11
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 12 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 230 +/- 30 N
- Stock lengths up to 2400 mm
- Very good running characteristics
- General applications
Power Transmission Belt Description
<standard belt choice>
PTBeltLength
x
RequiredBeltWidthInMm
x
PTBeltThickness
Running Side:
PTBeltRunningSide
Standard Part Description
PTBeltType2
PTBeltLength
x
RequiredBeltWidthInMm
x
PTBeltThickness
Running Side:
PTBeltRunningSide
Standard belts include PU 11, PU 12 and NE 22. These belts are available in length increments of 10 mm from 400-1800 mm long and from increments of 20 mm in length up to 2400 mm long. These belts may not be the most ideal belt within your specific application but are generally available with a 2 week delivery and no minimum order requirements. For some applications, they certainly are a perfect solution. When you have any type of special requirements (such as FDA approval) please select Custom Belt.
PU 11
- 55 Shore A foamed yellow PU
- Running side coated, outside textile
- Polyester Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 12 mm
- Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 230 +/- 30 N
- Preferred Lengths up to 2400 mm
- Very good running characteristics
- General applications
PU 12
- 55 Shore A foamed yellow, PU
- Running side coated, outside textile
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm
- Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
- Standard Lengths up to 2400 mm
- General Applications
- Medium Duty Drives
NE 22
- 75 Shore A textured black Neoprene
- Both sides coated
- Polyester Carcass
- Temp Range -20°C to 100°C
- Minimum Pulley Diameter = 20 mm
- Thickness = 1.4
- Required Shaft Load for 1% Elongation: 375 +/- 15 N
- Standard Lengths up to 2400 mm
- General Applications
- Medium Duty Drives
No special Requirements? If your application has no special requirements and your belt size is below 2400 mm, try a standard belt above.
In general, it is recommended to guide Esband truly endless woven flat belts using crowned pulleys. For recommendations on crown dimensions or which pulleys to crown, see pages 14-15 of our B210 Esband catalog. Of course, tracking guides are also an option. If you have any questions or concerns, contact our Applications Engineering department.
Polyurethane Belts (PU)
- Great for General Conveying
- Foamed (yellow, gray, white, red)
- Temperature Range up to 60°C
- Good coefficient of friction to paper
- Different durometers available (30, 55 and 70 Shore A)
- Thickness up to 10 mm
- Surface finishes: ground, non porous ply, low friction coating, silicone skim coat
PU 11
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 12 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 230 +/- 30 N
PU 17
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =15 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 950 +/- 50 N
PU 12
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
PU 18
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =30 mm (at standard thickness)
- Standard Thickness = 2.2 mm
- Required Shaft Load for 1% elongation: 1280 +/- 50 N
PU 0/6
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- No carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =8 mm (at standard thickness)
Standard Thickness: 0.9 mm
- 1.2 mm (from 1000mm length)
- 1.5 mm (from 1500 mm length)
- 2.0 mm (from 2000 mm length)
- Required Shaft Load for 1% elongation: 4 +/- 2 N
- Highly elastic
- friction lining
- for fixed shaft centers
- belts used as sets
- Requires operating or stretched length
PU elastic
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Rubber Cords / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 25 mm (at standard thickness)
- Standard Thickness = 1.8 mm
- Required Shaft Load for 1% elongation: 6 +/- 3N
- Elastic
- For fixed shaft centers
- Belts used as sets
- Requires operating or stretched length
PU elastic 13
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Rubber Cords / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 25 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 8 +/- 2N
- Elastic
- For fixed shaft centers
- Belts used as sets
- Requires operating or stretched length
PU 4/6
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 9 mm (at standard thickness)
- Standard Thickness = 0.8 mm
- Required Shaft Load for 1% elongation: 130 +/- 15N
- Accumulator conveyor
- Paper transport
- Very flexible
PU 10
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester/Polyamide
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 8 mm (at standard thickness)
- Standard Thickness = 0.9 mm
- Required Shaft Load for 1% elongation: 100 +/- 15N
- Slightly elastic
- For fixed shaft centers
- Belts used as sets
PU 20/1
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 9 mm (at standard thickness)
- Standard Thickness = 0.9 mm
- Required Shaft Load for 1% elongation: 165 +/- 15N
- Speed-up conveyor
- Knife edge
- Low coefficient of friction on textile side
PU 20
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester / Cotton
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 5 mm (at standard thickness)
- Standard Thickness = 0.8 mm
- Required Shaft Load for 1% elongation: 165 +/- 15N
- Thin, highly flexible
Compact Polyurethane (FX)
- FDA
- 80 Shore A
- Temperature Range -10°C - 80°C
- Surface finishes: smooth, ground or textured
- Only available in certain thicknesses
FX 11
80 Shore A, 92 Shore A
Polyester Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 10 mm (at standard thickness)
Standard Thickness = 1.4 mm
Required Shaft Load for 1% elongation: 230 +/- 20 N
FX 10
80 Shore A, 92 Shore A
Coated on both sides (ground one side, textured other)
Polyamide/Polyester Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 15 mm (at standard thickness)
Standard Thickness = 1.0 mm
Required Shaft Load for 1% elongation: 55 +/- 10 N
FX 17
80 Shore A, 92 Shore A
Kevlar Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 20 mm (at standard thickness)
Standard Thickness = 1.3 mm
Required Shaft Load for 1% elongation: 1040 +/- 50 N
FX 20
80 Shore A, 92 Shore A
Polyester/Cotton Carcass
Temp Range -10 to +80°C
Minimum Pulley Diameter = 15 mm (at standard thickness)
Standard Thickness = 0.7-0.9 mm
Required Shaft Load for 1% elongation: 165 +/- 15 N
Silicone (SI)
- FDA
- High and Low Temperature Resistance
- Temp Range: -60°C to 200°C
- 30-35 Shore A, 50 Shore A
- White, Gray, Red, Blue
- High coefficient of Friction
- Resistant to dirt and chemicals
- Great for printing applications
- Thickness up to 10 mm
- Surface finishes: ground, Silicone skim coat (sealed)
SI 1
30 Shore A, 50 Shore A
Polyester Carcass
White, Blue, Gray, Red
Temperature Range: -20°C to 150°C
Minimum Pulley Diameter: 12 mm (at standard thickness)
Standard Thickness = 1.0 mm
Required Shaft Load for 1% elongation: 190 +/- 20 N
SI 3
30 Shore A, 50 Shore A
Polyester/Cotton Carcass
White, Blue, Gray, Red
Temperature Range: -20°C to 120°C
Minimum Pulley Diameter: 10 mm (at standard thickness)
Standard Thickness = 1.0 mm
Required Shaft Load for 1% elongation: 135 +/- 15 N
HN 1
30 Shore A, 50 Shore A
Nomex Carcass
White, Blue, Gray, Red
Temperature Range: -50°C to 180°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 1.5 mm
Required Shaft Load for 1% elongation: 170 +/- 20 N
HG 1
30 Shore A, 50 Shore A
Fiberglass Carcass
White, Blue, Gray, Red
Temperature Range: -60°C to 200°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 1.5 mm
Required Shaft Load for 1% elongation: 600 +/- 50 N
HK 17
30 Shore A, 50 Shore A
Kevlar Carcass
White, Blue, Gray, Red
Temperature Range: -50°C to 200°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 1.3 mm
Required Shaft Load for 1% elongation: 290 +/- 50 N
HK 18
30 Shore A, 50 Shore A
Kevlar Carcass
White, Blue, Gray, Red
Temperature Range: -50°C to 200°C
Minimum Pulley Diameter: 20 mm (at standard thickness)
Standard Thickness = 2.0 mm
Required Shaft Load for 1% elongation: 990 +/- 100 N
Belt Part Description
PN1
PN2
PN3
PN4
Standard Part Description
PN1
PN8
PN7
FX Belt Part Description
PN1
PN2
PN6
PN5
PN4
NE 18
- 75 Shore A
- Kevlar carcass
- Temp range -20°C/+100°C
- Minimum pulley diameter = 30 mm (at standard thickness)
- Standard thickness = 2.0 mm
- Required shaft load for 1% elongation: 1700 +- 200 N
- Extremely low elongation
- Heavy-duty drives
NE 26
- 75 Shore A
- Polyester Carcass
- Temp range -20°C to +100°C
- Minimum Pulley Diameter = 25 mm
- Standard thickness = 2.0 mm
- Required shaft load for 1% elongation: 385 +/- 15 N
- Heavy Duty Drives
PU 18
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =30 mm (at standard thickness)
- Standard Thickness = 2.2 mm
- Required Shaft Load for 1% elongation: 1280 +/- 50 N
NE 22
- 75 Shore A
- Polyester Carcass
- Temp Range -20°C to +100°C
- Minimum pulley diameter = 20 mm
- Standard thickness = 1.4 mm
- Required shaft load for 1% elongation: 375 +/- 15 N
- Stocked lengths up to 2400 mm
- General applications
- Medium duty drives
NE 17
- 75 Shore A
- Kevlar Carcass
- Temp range -20°C to +100°C
- Minimum pulley diameter = 12 mm
- Standard thickness = 0.9 mm
- Required shaft load for 1% elongation: 1040 +/- 50 N
- Drive belt
- Very low elongation
PU 12
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
- Stock lengths up to 2400 mm
- General Applications
- Medium duty drives
PU 12
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass (impregnated)
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =20 mm (at standard thickness)
- Standard Thickness = 1.5 mm
- Required Shaft Load for 1% elongation: 290 +/- 30 N
- Stock lengths up to 2400 mm
- General Applications
- Medium duty drives
PU 17
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Kevlar Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter =15 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 950 +/- 50 N
- Very low elongation
NE 21
- 75 Shore A
- Polyester Carcass
- Temp Range -20°C to +100°C
- Minimum pulley diameter = 15 nn
- Standard thickness = 0.9 mm
- Required shaft load for 1% elongation: 270 +/- 10 N
- High belt speeds
- Very good running characteristics
- General applications
PU 11
- 30 Shore A (soft), 55 Shore A, 70 Shore A (hard)
- Polyester Carcass
- Temp Range -10 to +60°C
- Minimum Pulley Diameter = 12 mm (at standard thickness)
- Standard Thickness = 1.0 mm
- Required Shaft Load for 1% elongation: 230 +/- 30 N
- Stock lengths up to 2400 mm
- Very good running characteristics
- General applications
Power Transmission Belt Description
PTBeltType2
PTBeltLength
x
RequiredBeltWidthInMm
x
PTBeltThickness
Running Side:
PTBeltRunningSide
